Results 1 to 7 of 7
  1. #1
    Join Date
    Feb 2021
    Location
    Nova Scotia
    Posts
    5

    Default Ideas for Automatic Self-Closure on Interior Garage Door

    Hey Folks,

    Looking for some possible suggestions to pass along to a homeowner that is having difficulties acquiring his occupancy permit.

    Situation: Interior door leading to house from attached garage will not latch when garage door is closed so clearly there is insufficient strength in the sprung hinges to overcome the "pillow" of air contained within the garage itself, even at maximum tension. Homeowner doesn't want to install an overhead self-closure so my suggestion was going to be to try a product like this one since I can't think of a way to vent the pressure without compromising the building's thermal envelope - the garage is built as a conditioned space.



    Similar Threads:
    ***IMPORTANT*** You Need To Register To View Images ***IMPORTANT*** You Need To Register To View Images
    OREP Insurance

  2. #2
    Join Date
    Mar 2007
    Location
    Ormond Beach, Florida
    Posts
    27,539

    Default Re: Ideas for Automatic Self-Closure on Interior Garage Door

    Typically, one spring hinge is used, if only one is used, install another spring hinge, if necessary, install a spring hinge at all three hinge.

    If still necessary, add two more hinges to the door and use spring hinges.

    That's a secondary issue.

    The primary issue is that the garage should not be in the dwelling's thermal envelope.

    If the garage is conditioned space (separate from the dwelling unit), then vent the garage. It doesn't take much to vent a garage, and a garage that tight is a death trap.

    More likely, the house is so tight that the door is having problems closing - have you tried closing the other hinged exterior doors?

    If the house is that tight, then it likely needs a fresh air source in where the air handler furnace is.

    Jerry Peck
    Construction Litigation Consultant ( www.ConstructionLitigationConsultants.com )
    www.AskCodeMan.com

  3. #3
    Join Date
    Feb 2021
    Location
    Nova Scotia
    Posts
    5

    Default Re: Ideas for Automatic Self-Closure on Interior Garage Door

    Quote Originally Posted by Jerry Peck View Post
    Typically, one spring hinge is used, if only one is used, install another spring hinge, if necessary, install a spring hinge at all three hinge.

    If still necessary, add two more hinges to the door and use spring hinges.

    That's a secondary issue.

    The primary issue is that the garage should not be in the dwelling's thermal envelope.

    If the garage is conditioned space (separate from the dwelling unit), then vent the garage. It doesn't take much to vent a garage, and a garage that tight is a death trap.

    More likely, the house is so tight that the door is having problems closing - have you tried closing the other hinged exterior doors?

    If the house is that tight, then it likely needs a fresh air source in where the air handler furnace is.
    Thanks for the response Jerry!

    The homeowner has two spring hinges installed currently and it already swings like Babe Ruth so he's not keen to add more hinges, it's just that last inch or so to the latched position that's an issue. When the exterior garage door is open it slams shut with quite a bit of force.

    It's very common to have garages built into the thermal envelope here in Canada but normally the seal on the exterior garage door isn't this tight. The other exterior doors in the house feel normal to me, even when closed forcefully, but none of them have automatic closures so it's hard to be certain. The house is mechanically ventilated with an HRV and there's no furnace, just a couple heat pumps and a small woodstove.

    Not sure how to suggest venting the garage (conditioned space) to the homeowner as per code as I've never run into this issue before. Personally I would just cut a little piece out of the seal around the exterior garage door but I can't exactly suggest that to him LOL.

    Last edited by J Collins; 02-23-2021 at 07:26 AM.

  4. #4
    Join Date
    Feb 2008
    Location
    Chicago IL
    Posts
    2,028

    Default Re: Ideas for Automatic Self-Closure on Interior Garage Door

    If this is a typical pre-hung door assembly that we often see installed here as the service door to the garage, my guess is the threshold is sitting too high and causing too much resistance at the bottom of the door.
    Check the wood looking strip on top of the metal plate. There should be adjustment screws. Usually they are exposed, sometimes they are under a plastic cover. Adjusting those screws so there is less resistance should do the trick.
    May also want to check the strike plate make sure the latch isn't hitting it wrong causing resistance.

    www.aic-chicago.com
    773/844-4AIC
    "The Code is not a ceiling to reach but a floor to work up from"

  5. #5
    Join Date
    Feb 2021
    Location
    Nova Scotia
    Posts
    5

    Default Re: Ideas for Automatic Self-Closure on Interior Garage Door

    Quote Originally Posted by Markus Keller View Post
    If this is a typical pre-hung door assembly that we often see installed here as the service door to the garage, my guess is the threshold is sitting too high and causing too much resistance at the bottom of the door.
    Check the wood looking strip on top of the metal plate. There should be adjustment screws. Usually they are exposed, sometimes they are under a plastic cover. Adjusting those screws so there is less resistance should do the trick.
    May also want to check the strike plate make sure the latch isn't hitting it wrong causing resistance.
    Thanks Marcus, I did notice the strike plate was a bit mangled so that could be it but I'll suggest adjustment to the threshold first.


  6. #6
    Join Date
    Mar 2007
    Location
    Ormond Beach, Florida
    Posts
    27,539

    Default Re: Ideas for Automatic Self-Closure on Interior Garage Door

    Try this if it may be the strike plate: push the latch bolt in and tape it in, see if it closes.

    Could be the strike plate or even the latch bolt not sliding in easy enough.

    Jerry Peck
    Construction Litigation Consultant ( www.ConstructionLitigationConsultants.com )
    www.AskCodeMan.com

  7. #7
    Join Date
    Feb 2021
    Location
    Nova Scotia
    Posts
    5

    Default Re: Ideas for Automatic Self-Closure on Interior Garage Door

    Quote Originally Posted by Jerry Peck View Post
    Try this if it may be the strike plate: push the latch bolt in and tape it in, see if it closes.

    Could be the strike plate or even the latch bolt not sliding in easy enough.
    Thanks Jerry, I'll pass that suggestion along to the home owner. Really appreciate your input!


Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •