Results 1 to 9 of 9

Thread: Drain Waste

  1. #1
    David Banks's Avatar
    David Banks Guest

    Default Drain Waste

    Looks like a mess but does anyone see any issues? Second floor added with bath.

    Similar Threads:
    ***IMPORTANT*** You Need To Register To View Images ***IMPORTANT*** You Need To Register To View Images
    OREP Insurance

  2. #2
    Join Date
    Mar 2007
    Location
    Healdsburg, CA
    Posts
    1,741

    Default Re: Drain Waste

    A few.

    Jerry McCarthy
    Building Code/ Construction Consultant

  3. #3
    Brian E Kelly's Avatar
    Brian E Kelly Guest

    Default Re: Drain Waste

    Just to start the use of a tee instead of a wye, and lack of proper support.


  4. #4
    Scott Dana's Avatar
    Scott Dana Guest

    Default Re: Drain Waste

    At the bottom where the horizontal plastic line goes into the existing drain line, how is that attached? From the looks of the picture it appears to be resting in the line, although I doubt it really is.


  5. #5
    Join Date
    Apr 2007
    Location
    state of jefferson
    Posts
    522

    Default Re: Drain Waste

    the below the floor trap on the left appears to be without a vent.


  6. #6
    Martin lehman's Avatar
    Martin lehman Guest

    Default Re: Drain Waste

    There are quite a few problems in that picture. That setup looks like a do-it-yourselfer went to town. Defer it to a qualified plumber.


  7. #7
    Joshua Hardesty's Avatar
    Joshua Hardesty Guest

    Default Re: Drain Waste

    I'm really not even sure what I'm looking at.

    No support.
    No purple.
    That trap that's on the left -- Is that threaded? What about the one on the right?
    The trap on the left -- How long is that arm before reaches that 4" pipe?
    The trap on the right -- Where it goes into the 2" tee, underneath that, is that a short 90* change from verticle to horizontal?
    That's quite a few bends with no cleanouts.
    Hard to tell from the photo, but do those pipes have the right slope?
    Is everything vented properly?

    That trap on the left, when it reaches the 3", what kind of fitting is that going into? Is it a 3" tee with a 2" side inlet?

    Brian: Which tee are you referring to? I thought tees were acceptable when changing from horizontal to verticle.


    Scott: That small black ring around the PVC is a type of transition bushing. It's a large rubber ring that you shove inside the cast iron, then shove the PVC or ABS or into that. The pressures between the two create a seal.


  8. #8

    Default Re: Drain Waste

    I know this is an old thread, but looking at the fact that this was posted by a guest as his first post.
    I believe the lack of purple primer may indicate that the poster only temporarily fitted everything and is looking for advice before gluing it permanently.


  9. #9
    Join Date
    Mar 2007
    Location
    Fletcher, NC
    Posts
    28,042

    Default Re: Drain Waste

    Quote Originally Posted by David Crawford View Post
    I know this is an old thread, but looking at the fact that this was posted by a guest as his first post.
    I believe the lack of purple primer may indicate that the poster only temporarily fitted everything and is looking for advice before gluing it permanently.
    Purple primer is, as I recall, not required on DWV, however, I don't recall when that exception first began.

    DWV systems are not pressurized (unless the system is one of the few forced systems which are pressurized under use - in which case the exception from purple primer would not be applicable).

    Jerry Peck
    Construction/Litigation/Code Consultant - Retired
    www.AskCodeMan.com

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •