Results 1 to 20 of 20
  1. #1
    mathew stouffer's Avatar
    mathew stouffer Guest

    Default Creative Ridge Beam

    Check out this ridge beam. This place was built in 1994 and remodeled in 04. The glue lam was about 20 feet long and supported on each end by one 2x6.

    Similar Threads:
    ***IMPORTANT*** You Need To Register To View Images ***IMPORTANT*** You Need To Register To View Images
    Crawl Space Creeper

  2. #2
    Michael Garrity's Avatar
    Michael Garrity Guest

    Default Re: Creative Ridge Beam

    I"m not seeing the whole picture.


  3. #3
    Join Date
    Jun 2008
    Location
    Maryland
    Posts
    1,096

    Default Re: Creative Ridge Beam

    What size are those rafters? 2x10? They look bigger than you usually see. Also, since the glue lam has the rafters going over top of it instead of butting up to it, is it truly a ridge beam, or more of a purlin of sorts?


  4. #4
    Join Date
    Feb 2009
    Location
    Southern Vancouver Island
    Posts
    4,607

    Default Re: Creative Ridge Beam

    Pic 4 shows those 2X6's are the center webs of manufactured trusses, so the weight is shared by the truss chords. Also as John pointed out, the rafters are butted above the ridge beam, so a lot of the weight of the roof is directed out to the eaves by the rafters.
    The ceiling joists should act as rafter ties in this case, but they are not visible here.

    I don't see why they built it that way, but it does not look weak to me.


  5. #5
    mathew stouffer's Avatar
    mathew stouffer Guest

    Default Re: Creative Ridge Beam

    Do you think a 2x6 on each side end of the glue lam is enough support, also taking into consideration the snow loads. I know it's beyond the scope but the entire configuration JDLR.


  6. #6
    chris mcintyre's Avatar
    chris mcintyre Guest

    Default Re: Creative Ridge Beam

    Quote Originally Posted by John Kogel View Post
    Pic 4 shows those 2X6's are the center webs of manufactured trusses, so the weight is shared by the truss chords.
    Quote Originally Posted by mathew stouffer View Post
    Do you think a 2x6 on each side end of the glue lam is enough support, also taking into consideration the snow loads. I know it's beyond the scope but the entire configuration JDLR.
    I agree, it doesn't look right, but it also doesn't look like something that a framer would design on site.


  7. #7
    Join Date
    Feb 2009
    Location
    Southern Vancouver Island
    Posts
    4,607

    Default Re: Creative Ridge Beam

    Quote Originally Posted by mathew stouffer View Post
    Do you think a 2x6 on each side end of the glue lam is enough support, also taking into consideration the snow loads?
    Yep. There are knee walls in there as well. That beam is redundant, IMO.


  8. #8
    mathew stouffer's Avatar
    mathew stouffer Guest

    Default Re: Creative Ridge Beam

    Would you recommend additional evaluation?


  9. #9
    David Bell's Avatar
    David Bell Guest

    Default Re: Creative Ridge Beam

    The glue lam looks like it was meant to be exposed after framing.


  10. #10
    Join Date
    Mar 2008
    Location
    Charlotte NC
    Posts
    2,304

    Default Re: Creative Ridge Beam

    My guess is that the remodel in 04' required cutting out webbing of trusses. The beam was slid in to take the weight. Engineered? Signed letter? I think I would ask more questions about the remodel.


  11. #11
    mathew stouffer's Avatar
    mathew stouffer Guest

    Default Re: Creative Ridge Beam

    I am going to recommend further evaluation just to cover my butt.


  12. #12
    Kevin Stenson's Avatar
    Kevin Stenson Guest

    Cool Re: Creative Ridge Beam

    Why waste a nice glue lam beam in the attic they make cheaper ones


  13. #13
    Don Claeys's Avatar
    Don Claeys Guest

    Default Re: Creative Ridge Beam

    This appears to be a structural ridge beam. doesn't matter if rafters sit on top or hang off sides. Use of a structural ridge beam is normally to eliminate the need for collar ties or ceiling joists ie for a cathedral ceiling remodel. Can't see enough information about the 2x6 truss member bearing at the ends to comment.


  14. #14
    Join Date
    Jul 2008
    Location
    Utah
    Posts
    390

    Default Re: Creative Ridge Beam

    In reality a 2x6 can hold a tremendous amount of weight. However being in Park City you are in an active seismic zone and I would question the moment and shear capability more than the ability to support.

    The flex duct running below the beam looks small. Hopefully it's just for a toilet exhaust fan.


  15. #15
    Daniel Mummey's Avatar
    Daniel Mummey Guest

    Default Re: Creative Ridge Beam

    It appears to serve no real structural value for what appears to be a rafters to ridge gable type roof system UNLESS this beam span is intended to carry a future heavily loaded platform above the roof or a hoist below, in the case of a garage space below. In either case with the planned loading transferred to the ends and thus to the bearing walls (assumed) single 2 x 6 doesn't satisfy the crippling effect nor the safety factor. The total shear bolt capacities way exceed the bearing strength of the single 2 x 6.


  16. #16
    Join Date
    Mar 2008
    Location
    Charlotte NC
    Posts
    2,304

    Default Re: Creative Ridge Beam

    If ya'll didn't like the OP's pic's, your going to hate the one's I took today!

    ***IMPORTANT*** You Need To Register To View Images ***IMPORTANT*** You Need To Register To View Images

  17. #17
    Daniel Mummey's Avatar
    Daniel Mummey Guest

    Default Re: Creative Ridge Beam

    Keep it coming Vern. Great pictures. Apparently every single rafter mis-cut too short, thus the spliced ends to make the bearing to ridge. Now tell me this is the tool shed or some other non-residential structure the building authority passed by!


  18. #18
    Join Date
    Mar 2008
    Location
    Charlotte NC
    Posts
    2,304

    Default Re: Creative Ridge Beam

    Quote Originally Posted by Daniel Mummey View Post
    Keep it coming Vern. Great pictures. Apparently every single rafter mis-cut too short, thus the spliced ends to make the bearing to ridge. Now tell me this is the tool shed or some other non-residential structure the building authority passed by!
    I, and the owner, would like to tell you that but......


  19. #19
    Join Date
    Jul 2008
    Location
    Utah
    Posts
    390

    Default Re: Creative Ridge Beam

    Quote Originally Posted by Vern Heiler View Post
    If ya'll didn't like the OP's pic's, your going to hate the one's I took today!

    wow. . . if it weren't so tragic it would be entertaining.


  20. #20
    Join Date
    Jul 2009
    Location
    Cincinnati area
    Posts
    34

    Default Re: Creative Ridge Beam

    If you look at the third photo, you can see a gap between the rafters and the beam at least on one side. It likely is only supporting its own weight. Is it possible that this beam is left from previous construction?

    Either way, if I were doing a structural inspection on this one, I would likely say "OMG!" and state that I did not see a problem.


Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •