Results 1 to 8 of 8
  1. #1
    Barry Thistlethwaite's Avatar
    Barry Thistlethwaite Guest

    Default Flashing/Counter-flashing with Board-Batten siding

    The builder of my attached garage installed step flashing against the board and batten siding where my new roof meets the existing house. The step flashing was flush with the battens and left a nearly 1-inch gap between the flashing and the boards. The contractor said not to worry, the roofer would install counter flashing. Instead, he hammered the step flashing to conform to the boards and battens, and put caulk along the top. I contend this will start to leak in a few years as the metal expands and contracts against the wood.

    How should this be done? My understanding is that counter flashing should always go underneath siding. But I can't find anything specific to board-and-batten. What needs to happen here?

    Similar Threads:
    ***IMPORTANT*** You Need To Register To View Images ***IMPORTANT*** You Need To Register To View Images
    Member Benefits1

  2. #2
    Join Date
    Aug 2012
    Location
    Rock Hill S.C.
    Posts
    95

    Default Re: Flashing/Counter-flashing with Board-Batten siding

    Quote Originally Posted by Barry Thistlethwaite View Post
    How should this be done? My understanding is that counter flashing should always go underneath siding. But I can't find anything specific to board-and-batten. What needs to happen here?
    What you have is wrong.
    Board and batten siding is no different than any other siding (as far as step flashing goes).
    The siding should have been cut at the roof line, removed, flashed and reinstalled...or the b&b could be cut back 5" +/- and a trim board running with the rake installed with a Z flashing at the transition and the step flashing behind the trim board, this is somewhat of a shortcut so the siding does not need to be removed.

    Counter flashing is a method used when flashing to a masonry wall.


  3. #3
    Barry Thistlethwaite's Avatar
    Barry Thistlethwaite Guest

    Default Re: Flashing/Counter-flashing with Board-Batten siding

    Quote Originally Posted by Chris McIntyre View Post
    What you have is wrong.
    Board and batten siding is no different than any other siding (as far as step flashing goes).
    The siding should have been cut at the roof line, removed, flashed and reinstalled...or the b&b could be cut back 5" +/- and a trim board running with the rake installed with a Z flashing at the transition and the step flashing behind the trim board, this is somewhat of a shortcut so the siding does not need to be removed.

    Counter flashing is a method used when flashing to a masonry wall.
    Thank you, Chris! To clarify, if they pull the siding and put step flashing behind it, you're saying no other flashing is required? Or if they install the trim board over the step flashing, Z flashing goes...where, on top of the trim board, down the face, and then under the shingles?

    My contractor says he is hiring another company to come in and fix it. I want to know what to look for when they do--or what I will have to hire someone to do if he doesn't get it right.


  4. #4
    Join Date
    Aug 2012
    Location
    Rock Hill S.C.
    Posts
    95

    Default Re: Flashing/Counter-flashing with Board-Batten siding

    Quote Originally Posted by Barry Thistlethwaite View Post
    To clarify, if they pull the siding and put step flashing behind it, you're saying no other flashing is required?
    Correct

    Quote Originally Posted by Barry Thistlethwaite View Post
    Or if they install the trim board over the step flashing, Z flashing goes...where, on top of the trim board, down the face, and then under the shingles?
    Z flashing goes behind the siding and terminates outside the trim board.

    ***IMPORTANT*** You Need To Register To View Images ***IMPORTANT*** You Need To Register To View Images

  5. #5
    Barry Thistlethwaite's Avatar
    Barry Thistlethwaite Guest

    Default Re: Flashing/Counter-flashing with Board-Batten siding

    Quote Originally Posted by Chris McIntyre View Post
    Correct



    Z flashing goes behind the siding and terminates outside the trim board.
    Chris, thank you so much! the diagram explains it very clearly. I appreciate the help!


  6. #6
    Barry Thistlethwaite's Avatar
    Barry Thistlethwaite Guest

    Default Re: Flashing/Counter-flashing with Board-Batten siding

    Quote Originally Posted by Barry Thistlethwaite View Post
    Chris, thank you so much! the diagram explains it very clearly. I appreciate the help!
    OK, they cut the battens and installed a board as you described, but the flashing on top of the board is L-flashing, not Z-flashing, and does not go under the siding. It seems to me the only thing keeping my house dry is still caulk, not flashing. Is this what you were referring to in your second option?

    ***IMPORTANT*** You Need To Register To View Images ***IMPORTANT*** You Need To Register To View Images

  7. #7
    Join Date
    Aug 2012
    Location
    Rock Hill S.C.
    Posts
    95

    Default Re: Flashing/Counter-flashing with Board-Batten siding

    Quote Originally Posted by Barry Thistlethwaite View Post
    It seems to me the only thing keeping my house dry is still caulk, not flashing.
    Correct.

    Quote Originally Posted by Barry Thistlethwaite View Post
    Is this what you were referring to in your second option?
    Not even close, this is really no different than what you had the first time!
    If I were using the trim board I would cut the board and batten siding, make sure the Z flashing is under the WRB. If the trim board is going to sit on the roof it should be treated and if it is treated you cannot use the aluminum trim coil.
    There is more than one way to make this repair, the current builder has had two shots at it, and got it wrong twice. If you had not questioned him it would have been left this way. You may want to consider someone else (another builder or an inspector) taking a look at your addition and make sure there are no other issues.


  8. #8
    Join Date
    Apr 2011
    Location
    Bozeman, Montana
    Posts
    94

    Default Re: Flashing/Counter-flashing with Board-Batten siding




Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •