Results 1 to 23 of 23
  1. #1
    John Stephenson's Avatar
    John Stephenson Guest

  2. #2
    Join Date
    Oct 2003
    Location
    Rockwall Texas
    Posts
    4,521

    Default Re: How are repairs performed

    You should move on to bigger issues.

    JMHO


  3. #3
    Join Date
    Mar 2007
    Location
    Houston, Texas
    Posts
    294

    Default Re: How are repairs performed

    If its going to be repaired at all it should be done correctly. In the first photo that would involve removing the cable end patch material and opening up the cable end pocket again. The end of the steel cable then needs to be greased and have a plastic end cap installed. Then grout the open cable end pocket back in with non-shrinking grout cement.

    The second photo looks more like a nail that held one of the cable end flanges to the form board rather than a cable tendon end. If it is a cable end, then the above procedure all over again.

    The way these will most likely be repaired if they are repaired at all will be to butter over the spots with a little more grout cement to hid the rusty spots that are forming.


  4. #4
    Join Date
    Oct 2003
    Location
    Rockwall Texas
    Posts
    4,521

    Default Re: How are repairs performed

    His weep holes are a bigger problem than that cable end (looks like a nail) in my opinion.


  5. #5
    Richard Rushing's Avatar
    Richard Rushing Guest

    Default Re: How are repairs performed

    The first one is a cable end... The only proper repair was described by Philip.

    However, it is never done that way. The glazing cover is all that is ever done.

    Nails... who cares. Like Rick H says, move on to bigger things.

    Rich


  6. #6
    Join Date
    Mar 2007
    Location
    Fletcher, NC
    Posts
    28,032

    Default Re: How are repairs performed

    Quote Originally Posted by Richard Rushing View Post
    The first one is a cable end...
    Man, that's the smallest cable I've ever seen.

    I'd say it was the end of WWM, or ... a nail ...

    Jerry Peck
    Construction/Litigation/Code Consultant - Retired
    www.AskCodeMan.com

  7. #7
    Richard Rushing's Avatar
    Richard Rushing Guest

    Default Re: How are repairs performed

    I guess it is the smallest you've ever seen, JP.

    That first one is definately a cable end. To the right of the cable end is a batter board nail and to the left is... No batter board nail (covered).

    Rich


  8. #8
    Join Date
    Mar 2007
    Location
    Fletcher, NC
    Posts
    28,032

    Default Re: How are repairs performed

    Quote Originally Posted by Richard Rushing View Post
    I guess it is the smallest you've ever seen, JP.
    Rich,

    I'm game ...

    What size is that "cable"?

    1"?

    1/2"?

    1/4"?

    1/8"?

    1/16"?

    Jerry Peck
    Construction/Litigation/Code Consultant - Retired
    www.AskCodeMan.com

  9. #9
    Richard Rushing's Avatar
    Richard Rushing Guest

    Default Re: How are repairs performed

    Can't tell Jerry. The actual circumference (outside diameter) is covered. What you are seeing there is only part of the end (the inside part).

    Are you saying that this is *NOT* a cable end???? Huh??

    Rich


  10. #10
    Join Date
    Mar 2007
    Location
    Houston, Texas
    Posts
    294

    Default Re: How are repairs performed

    Jerry,

    The first photo does look to me like a grouping of the individual strands that make up the individual cable tendons. The steel in the tendons used around here are typically about ½ to 5/8 inch in diameter and are comprised of several individual strands about the thickness of a 16d nail each and all grouped together within a plastic sheathing. The sawn end of the cable looks just like that dot pattern in the first photo.

    Are you seeing something different?



  11. #11
    Join Date
    Mar 2007
    Location
    Fletcher, NC
    Posts
    28,032

    Default Re: How are repairs performed

    Quote Originally Posted by Richard Rushing View Post
    Are you saying that this is *NOT* a cable end???? Huh??

    Rich
    Yep. That's what I'm saying.

    Looks WAY TOO SMALL to be a cable end.

    Jerry Peck
    Construction/Litigation/Code Consultant - Retired
    www.AskCodeMan.com

  12. #12
    Join Date
    Mar 2007
    Location
    Fletcher, NC
    Posts
    28,032

    Default Re: How are repairs performed

    Quote Originally Posted by Phillip Stojanik View Post
    Jerry,

    The first photo does look to me like a grouping of the individual strands that make up the individual cable tendons.
    It looked like a grouping of individual strands to me, however, a grouping of strands is not strands wrapped around a much larger single center cable - as would be with the pattern shown in that photo.

    Besides ...

    The steel in the tendons used around here are typically about ½ to 5/8 inch in diameter


    If that "cable end" is 1/2" or 5/8" ... how big is that brick above it?

    Look at the size of the 1/2" or 5/8" cable (assume that is what it is) and look at the relative size of that 3/8" mortar joint. Is that mortar joint, which is about twice as thick as that rust spot, really 1" or greater?

    How big would that brick be if that mortar joint is 1" or greater? HUGE!

    I really doubt it.

    and are comprised of several individual strands about the thickness of a 16d nail each and all grouped together within a plastic sheathing. The sawn end of the cable looks just like that dot pattern in the first photo.

    Are you seeing something different?
    Yes.

    I am seeing something smaller than 3/8" in diameter, maybe more like 3/16" to 1/4" in diameter or less.

    Which is why I say it is not a cable - I've never seen a PT cable that small.

    Jerry Peck
    Construction/Litigation/Code Consultant - Retired
    www.AskCodeMan.com

  13. #13
    Join Date
    Mar 2007
    Location
    Plano, Texas
    Posts
    4,245

    Default Re: How are repairs performed

    This is a small issue as Rick said, but I can't resist.
    Jerry, are you looking at the same picture? I am looking at the left picture without the arrow.
    "I " can't get any dimensions off of anything in that picture since it is stone, not brick and mortar joints will vary as will size of weeps.
    The total end of the cable does not appear to be visible, it appears partially obscured by cement around the circumference, IMO.
    The small rust spot a short distance to the right does appear the right size and location for a form nail.
    I agree with others, this is the usual appearance of a cable end for post tension as is common to this local.
    The right photo is just a nail.

    Jim Luttrall
    www.MrInspector.net
    Plano, Texas

  14. #14
    Join Date
    Mar 2007
    Location
    Fletcher, NC
    Posts
    28,032

    Default Re: How are repairs performed

    Quote Originally Posted by Jim Luttrall View Post
    Jerry, are you looking at the same picture? I am looking at the left picture without the arrow.
    You tell me. See attached drawing.

    I agree with others, this is the usual appearance of a cable end for post tension as is common to this local.[/quote]

    Please take a photo of the next cable end you see and post it for me, okay?

    Thanks.

    ***IMPORTANT*** You Need To Register To View Images ***IMPORTANT*** You Need To Register To View Images
    Jerry Peck
    Construction/Litigation/Code Consultant - Retired
    www.AskCodeMan.com

  15. #15
    Richard Rushing's Avatar
    Richard Rushing Guest

    Default Re: How are repairs performed

    You asked....

    The one on the left in Johns picture looks like the one on the left in my photo below...

    That IS a post tensioned cable. Again, not all of the cable is exposed.

    Rich

    ***IMPORTANT*** You Need To Register To View Images ***IMPORTANT*** You Need To Register To View Images

  16. #16
    Join Date
    Oct 2003
    Location
    Rockwall Texas
    Posts
    4,521

    Default Re: How are repairs performed

    I think what is present in John's picture is the same as in the one below.

    Nail heads.

    ***IMPORTANT*** You Need To Register To View Images ***IMPORTANT*** You Need To Register To View Images

  17. #17
    Join Date
    Mar 2007
    Location
    Fletcher, NC
    Posts
    28,032

    Default Re: How are repairs performed

    Quote Originally Posted by Richard Rushing View Post
    You asked....

    The one on the left in Johns picture looks like the one on the left in my photo below...
    Rich,

    Nope.

    John's photo does not look like that. In MY drawing, the left one looks like your cable, but John's photo looks like my right drawing - which does not look like your cable.

    Jerry Peck
    Construction/Litigation/Code Consultant - Retired
    www.AskCodeMan.com

  18. #18
    Richard Rushing's Avatar
    Richard Rushing Guest

    Default Re: How are repairs performed

    Jerry, I don't know what your eyes are seeing....

    But, the rest of us who see the real cables every day (and not some cartoon) are absolutely sure when we see the real deal.

    Oh well... I'm sure you guys seen these every day too.

    Rich


  19. #19
    Join Date
    Mar 2007
    Location
    Fletcher, NC
    Posts
    28,032

    Default Re: How are repairs performed

    Rich,

    I'm seeing the same thing Rick is seeing.

    Jerry Peck
    Construction/Litigation/Code Consultant - Retired
    www.AskCodeMan.com

  20. #20
    Join Date
    Mar 2007
    Location
    Plano, Texas
    Posts
    4,245

    Default Re: How are repairs performed

    Jerry, clean your glasses and take a closer look

    Jim Luttrall
    www.MrInspector.net
    Plano, Texas

  21. #21
    Join Date
    Mar 2007
    Location
    Plano, Texas
    Posts
    4,245

    Default Re: How are repairs performed

    now look at the picture

    ***IMPORTANT*** You Need To Register To View Images ***IMPORTANT*** You Need To Register To View Images
    Jim Luttrall
    www.MrInspector.net
    Plano, Texas

  22. #22
    Join Date
    Mar 2007
    Location
    Fletcher, NC
    Posts
    28,032

    Default Re: How are repairs performed

    Quote Originally Posted by Jim Luttrall View Post
    now look at the picture
    Right, like the RIGHT one in my drawing.

    NOT like the left one, which shows a typical cable.

    The only person who can answer this is John, and only then if he knows approximately how large that spot is, or what size the bricks/stones are.

    It's nice to have a tape measure or something of size reference in the photo.

    Jerry Peck
    Construction/Litigation/Code Consultant - Retired
    www.AskCodeMan.com

  23. #23
    Join Date
    Mar 2007
    Location
    Corpus Christi, TX
    Posts
    615

    Default Re: How are repairs performed

    Which unit of measure tape; British, metric, or the one we use to estimate the size of our manhoods? If the latter is used, I would estimate its diameter at about 4 inches.

    The only reason some people get lost in thought is because it's unfamiliar territory.
    - Paul Fix

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •