Results 1 to 18 of 18

Thread: Notched joist

  1. #1
    mathew stouffer's Avatar
    mathew stouffer Guest

    Default Notched joist

    Approximately 3 inches was notched out of the middle span of this joist. What is the max allowable for notching the middle third, 1/6 or 1/3? I cant remember.

    Similar Threads:
    Crawl Space Creeper

  2. #2
    mathew stouffer's Avatar
    mathew stouffer Guest

    Default Re: Notched joist

    Long day, I gues pics would help

    ***IMPORTANT*** You Need To Register To View Images ***IMPORTANT*** You Need To Register To View Images

  3. #3
    Join Date
    Mar 2007
    Location
    Knoxville, TN
    Posts
    2,560

    Default Re: Notched joist

    You can't notch ANY part in the middle third of the span.


  4. #4

    Default Re: Notched joist

    Yep, no notching in the middle third.
    The only time I've seen subfloor material like that is in manufactured homes-- what is it?


  5. #5
    mathew stouffer's Avatar
    mathew stouffer Guest

    Default Re: Notched joist

    Built in 76. I think it may have been at one time but there have been some custom touches added.


  6. #6
    David Bell's Avatar
    David Bell Guest

    Default Re: Notched joist

    Good old particle board sub floor, expands to 1.5 times its normal width when wet. Then disintegrates.


  7. #7
    Join Date
    Jul 2010
    Location
    Tennessee
    Posts
    66

    Default Re: Notched joist

    To answer your second question, it is 1/6 the joist or 1.5" in this case.


  8. #8
    Join Date
    Apr 2008
    Location
    Massachusetts
    Posts
    195

    Default Re: Notched joist

    "R502.8.1 Sawn lumber.
    Notches in solid lumber joists, rafters and beams shall not exceed one-sixth of the depth of the member, shall not be longer than one-third of the depth of the member and shall not be located in the middle one-third of the span. Notches at the ends of the member shall not exceed one-fourth the depth of the member. The tension side of members 4 inches (102 mm) or greater in nominal thickness shall not be notched except at the ends of the members. The diameter of holes bored or cut into members shall not exceed one-third the depth of the member. Holes shall not be closer than 2 inches (51 mm) to the top or bottom of the member, or to any other hole located in the member. Where the member is also notched, the hole shall not be closer than 2 inches (51 mm) to the notch."


  9. #9
    Join Date
    Jun 2010
    Location
    Vancouver
    Posts
    202

    Default Re: Notched joist

    Partical board for flooring. not a good idea, as to the notching also not a good idea. something not asked too is what is the span of the notched joist? this has a bearing how safe it is too. if it is a short span I wouldn't worry too much but a large span is of major concern. Also what was that wire there and it looked like it wasn't secured properly too.


  10. #10
    David Valley's Avatar
    David Valley Guest

    Default Re: Notched joist

    Image of joist notching allowed....

    ***IMPORTANT*** You Need To Register To View Images ***IMPORTANT*** You Need To Register To View Images

  11. #11
    Join Date
    Jul 2010
    Location
    Tennessee
    Posts
    66

    Default Re: Notched joist

    Great drawing, thanks


  12. #12
    Join Date
    Mar 2008
    Location
    Rocky Mountains of Boulder, CO
    Posts
    158

    Default Re: Notched joist

    Quote Originally Posted by mathew stouffer View Post
    Approximately 3 inches was notched out of the middle span of this joist. What is the max allowable for notching the middle third, 1/6 or 1/3? I cant remember.
    http://www.inspectionnews.net/home_i...854-post3.html


  13. #13
    Join Date
    Dec 2008
    Location
    Maryland
    Posts
    2,809

    Default Re: Notched joist

    Mat,
    Are you in the Home Inspection business?
    If yes;
    Do you maintain a personal library for reference?
    Do you keep any code or other reference materials in your vehicle when you go on an inspection?
    Do you take a laptop with you to your inspections?


  14. #14
    Join Date
    Jul 2008
    Location
    Snowbird (this means I'm retired and migrate between locations), FL/MI
    Posts
    4,086

    Default Re: Notched joist

    Since when is the IRC used to inspect post 74 legislation/post 1976 eff. date manufactured homes (a.k.a. coach homes, mobile homes, trailers, single-wides/double-wides, etc.)?

    Federal Register for the code which such are made. If the registration number hasn't been pulled or altered.

    You'll find that 76 date on all, current (post effective 74 legislation Fed. Standard) manufactured homes and referenced a few places usually, not the same as actual mfg date, for that you have to distinguish on the registration tag/plate.

    Just love it when you find NM unsecured, draped below joists & wrapped around a metal water pipe section don't you? Notching/hacking, particle/mdf board sub floor and bracing, ABS DWV, bad copper joints and PB pipe, bonanza!

    What custom touches besides the hacked plumbing repairs and elect.modification?

    Last edited by H.G. Watson, Sr.; 11-20-2010 at 01:17 PM.

  15. #15
    Join Date
    Jul 2008
    Location
    Snowbird (this means I'm retired and migrate between locations), FL/MI
    Posts
    4,086

    Default Re: Notched joist

    Quote Originally Posted by Garry Sorrells View Post
    Mat,
    Are you in the Home Inspection business?
    If yes;
    Do you maintain a personal library for reference?
    Do you keep any code or other reference materials in your vehicle when you go on an inspection?
    Do you take a laptop with you to your inspections?

    OOooh, Ouch. Question number 1. Don't read much on the site or visit regularly until perhaps recently, Huh, Garry Sorrells?

    Question 2, No comment, except: "Brace yourself for impact!". (Been there, )

    Questions 3 & 4, Who cares what he carries in his vehicle or at inspection, if he's finalizing reporting off-site or in personal space afterwards?!? Some walk around with a camera and digital recorder without a laptop or checklist program, why is this relevant to you?


  16. #16
    mathew stouffer's Avatar
    mathew stouffer Guest

    Default Re: Notched joist

    Gary I asked a simple question,yes it was very simple. I dont need to deal with **** from you. If you don't like the question move on.


  17. #17
    Join Date
    Mar 2008
    Location
    Rocky Mountains of Boulder, CO
    Posts
    158

    Default Re: Notched joist

    Quote Originally Posted by mathew stouffer View Post
    Long day, I gues pics would help

    Mathew,
    The crack in the board coming from the left is also a concern. Yes?
    And remember, the overcuts are part of the notch measurement. Think of a cut in a board as a very narrow notch.


  18. #18
    Join Date
    Dec 2008
    Location
    Maryland
    Posts
    2,809

    Default Re: Notched joist

    Quote Originally Posted by Garry Sorrells View Post
    Mat,
    Are you in the Home Inspection business?
    If yes;
    Do you maintain a personal library for reference?
    Do you keep any code or other reference materials in your vehicle when you go on an inspection?
    Do you take a laptop with you to your inspections?


    Mat,
    Not intended as snotty question. Sorry to offend you. Thin skinned? Ego issues? Question was intended to see what others maintain for reference when the mind gets fuzzy. A butcher, baker and a candle stick maker could have the same question, just curious where you were coming from.

    Yes it was a simple question you asked.
    You may have added what the span was since that would affect the rating for the remaining wood left after notching. If it was over engineered and then notched, leaving sufficient lumber to meet span requirement then notch may be a non issue.

    I am always on the look out for reference info. I have condensed code charts, books, downloaded county-state-national building code, journal articles, manufacture installation instructions, etc. and the list keeps growing thanks to the electronic age. I even have reference books dated from 1910 (wife's grand father was a mason, builder, teacher), not that I will need the load factors to build a buttressed wall for a cathedral, but there is other information included. Knowledge is strength.


Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •