Results 1 to 15 of 15
  1. #1
    Ron Bibler's Avatar
    Ron Bibler Guest

    Talking Electrical shock from the cover of this Zinsco panel

    I Removed the cover from this Zinsco panel today and dang what happened to the guy that did this

    Don't let this be you

    I did not re-install the cover... I tape the door off for Safety... The owner need to call Sparky. A.S.A.P.

    Best

    Ron Bibler
    Santa Rosa California Home Inspection - Exterminating & Thermal Imaging
    www.sonomehomeinspection.com

    Similar Threads:
    ***IMPORTANT*** You Need To Register To View Images ***IMPORTANT*** You Need To Register To View Images
    Last edited by Ron Bibler; 08-14-2011 at 11:08 AM.
    Inspection Referral

  2. #2
    James Duffin's Avatar
    James Duffin Guest

    Default Re: Electrical shock from the cover of this Zinsco panel

    I alway tape the top with several layers of tape before I put them back on.


  3. #3
    Join Date
    Mar 2007
    Location
    Charlotte NC Licensed in NC and SC
    Posts
    597

    Default Re: Electrical shock from the cover of this Zinsco panel

    I recently finished my required NC training for electrical safety. I learned that those Zinsco panels were originally considered part of the service equipment and were not intended to have the inside cover removed without first removing the meter to disable the power. I don't remove meters and that panel needs replacing for other reasons.

    Bruce King, B.A. King Home Inspections, LLC
    www.BAKingHomeInspections.com
    Certified Master Inspector, Independent Inspectorwww.IndependentInspectors.org

  4. #4
    Join Date
    Mar 2007
    Location
    Santa Rosa, CA
    Posts
    3,154

    Default Re: Electrical shock from the cover of this Zinsco panel

    Quote Originally Posted by Ron Bibler View Post
    I Removed the cover from this Zinsco panel today and dang what happened to the guy that did this
    I'm fine Ron. Thanks for asking.

    Department of Redundancy Department
    Supreme Emperor of Hyperbole
    http://www.FullCircleInspect.com/

  5. #5
    Roger Frazee's Avatar
    Roger Frazee Guest

    Default Re: Electrical shock from the cover of this Zinsco panel

    Failure to follow the cover removal instructions attached on the inside surface of the panel cover ...


  6. #6
    Ron Bibler's Avatar
    Ron Bibler Guest

    Default Re: Electrical shock from the cover of this Zinsco panel

    Quote Originally Posted by Roger Frazee View Post
    Failure to follow the cover removal instructions attached on the inside surface of the panel cover ...
    I would bet this happened when the they were trying to put the cover back on. Not from trying to remove it...

    At any point these panels can bite big time. look at this other arc flash point in the panel. at first i was thinking some one was doing some repairs. But after thinking about it this was part of the original arc flash.

    OUCH!

    Best

    Ron

    ***IMPORTANT*** You Need To Register To View Images ***IMPORTANT*** You Need To Register To View Images

  7. #7
    Join Date
    Mar 2007
    Location
    Spring Hill (Nashville), TN
    Posts
    5,851

    Default Re: Electrical shock from the cover of this Zinsco panel

    Reason #2 for not removing the cover of a Zinsco panel!

    Scott Patterson, ACI
    Spring Hill, TN
    www.traceinspections.com

  8. #8
    Join Date
    Feb 2010
    Location
    Long Beach, CA
    Posts
    105

    Default Re: Electrical shock from the cover of this Zinsco panel

    Here's a nearly burned-through meter bar on a Pushmatic...

    ***IMPORTANT*** You Need To Register To View Images ***IMPORTANT*** You Need To Register To View Images

  9. #9
    Ron Bibler's Avatar
    Ron Bibler Guest

    Default Re: Electrical shock from the cover of this Zinsco panel

    Quote Originally Posted by Marc Morin View Post
    Here's a nearly burned-through meter bar on a Pushmatic...
    Marc... Do you have some more photos of that panel.

    Best

    Ron


  10. #10
    Join Date
    May 2010
    Location
    No. San Diego Co., CA
    Posts
    562

    Default Re: Electrical shock from the cover of this Zinsco panel

    While on the subject of panels and dead-fronts...Here's an interesting 'find' from recent inspection.

    The deadfront was replaced with a sheet of plastic, with cut-outs to accommodate the breakers. The plastic was then trimmed with 1/4 round and completely hot-glued in place, including gluing some of the breakers...I guess they were a bit loose!. The innovator had the presence of mind to make it 'look nice' by spraying it matte black.

    No, I did not even attempt to remove it.

    ***IMPORTANT*** You Need To Register To View Images ***IMPORTANT*** You Need To Register To View Images

  11. #11

    Default Re: Electrical shock from the cover of this Zinsco panel

    Quote Originally Posted by Ian Page View Post
    While on the subject of panels and dead-fronts...Here's an interesting 'find' from recent inspection.

    The deadfront was replaced with a sheet of plastic, with cut-outs to accommodate the breakers. The plastic was then trimmed with 1/4 round and completely hot-glued in place, including gluing some of the breakers...I guess they were a bit loose!. The innovator had the presence of mind to make it 'look nice' by spraying it matte black.

    No, I did not even attempt to remove it.
    I suppose its better than NO dead front.

    True Professionals, Inc. Property Consultant
    877-466-8504

  12. #12
    Ron Bibler's Avatar
    Ron Bibler Guest

    Default Re: Electrical shock from the cover of this Zinsco panel

    Quote Originally Posted by Dana Bostick View Post
    I suppose its better than NO dead front.
    Kinda make you think ? What became of the original cover?

    Did he use it to make something else. Like a cover for his tractor with a bit of duct tape

    Best

    Ron


  13. #13
    Join Date
    Feb 2010
    Location
    Long Beach, CA
    Posts
    105

    Default Re: Electrical shock from the cover of this Zinsco panel

    Ron,

    Here you go...

    ***IMPORTANT*** You Need To Register To View Images ***IMPORTANT*** You Need To Register To View Images

  14. #14
    Join Date
    Feb 2010
    Location
    Long Beach, CA
    Posts
    105

    Default Re: Electrical shock from the cover of this Zinsco panel

    Ron,

    A few more...

    ***IMPORTANT*** You Need To Register To View Images ***IMPORTANT*** You Need To Register To View Images

  15. #15
    Binford Tools's Avatar
    Binford Tools Guest

    Default Re: Electrical shock from the cover of this Zinsco panel

    Good ole Zinsco. Where you inspecting how tight the lugs were on the breakers, or some pink or blue or other color wiring?

    I just push each breaker slowly to the off position noting how far one has to push it. If you get to the off position and the breaker has not tripped, that's a problem. A new one trips at 1/3 of the way to off. So if they go much past the half way mark the breaker spring is toast.


Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •