Results 1 to 29 of 29
  1. #1
    Matthew Liang's Avatar
    Matthew Liang Guest

    Default Plastic hot water supply pipe too close to heater

    I am a new CAHPI(BC) candidate. I inspected my friend's home today as a practice. I found that the hot water supply pipe near the tank is red plastic. I remember that the hot water pipe has to be copper within 18' close to the tank. Is it okay to use this find of plastic pipe. Sorry that the picture is blurred.

    Any comment is appreciated.

    Similar Threads:
    ***IMPORTANT*** You Need To Register To View Images ***IMPORTANT*** You Need To Register To View Images
    Crawl Space Creeper

  2. #2
    Join Date
    Dec 2007
    Location
    Holladay, UT
    Posts
    577

    Default Re: Plastic hot water supply pipe too close to heater

    In my area it's not ok to have pex within 18" oy top of water heater (I'm assuming that's pex). Is that gray pipe you can see in the wall behind heater polybutylene?

    Tom Rees / A Closer Look Home Inspection / Salt Lake City, Utah
    http://acloserlookslc.com/

  3. #3
    Join Date
    Feb 2009
    Location
    Southern Vancouver Island
    Posts
    4,607

    Default Re: Plastic hot water supply pipe too close to heater

    Red, blue or bright white flexible pipe is most likely to be PEX.
    Instead of 'plastic' try to use the correct terms like poly or vinyl or PolyB or Pex or PVC.
    The hard cream colored pipe is CPVC. You will find that occasionally, no longer used.

    PEX can handle the heat of the water heater, and we see it used that way fairly often, such as if a new tank has been installed in an older house. It is incorrect by the rule.

    John Kogel, RHI, BC HI Lic #47455
    www.allsafehome.ca

  4. #4
    Join Date
    Mar 2007
    Location
    Spring Hill (Nashville), TN
    Posts
    5,851

    Default Re: Plastic hot water supply pipe too close to heater

    Yes, the PEX can handle the hot water but not the hot exhaust gas from the burner.... You need to see 18" of metal pipe and then the PEX.

    Scott Patterson, ACI
    Spring Hill, TN
    www.traceinspections.com

  5. #5
    Matthew Liang's Avatar
    Matthew Liang Guest

    Default Re: Plastic hot water supply pipe too close to heater

    Thanks everybody for your comments.

    Tom, the gray pipe is PolyB which is used for all the supply pipes.

    So, I can conclude that the red pipe is PEX and it is too close to the heater.


  6. #6
    Join Date
    Jun 2008
    Location
    St. Thomas Ontario, Canada
    Posts
    59

  7. #7
    Join Date
    May 2012
    Location
    Western Maryland
    Posts
    131

    Default Re: Plastic hot water supply pipe too close to heater

    At minimum I always recommend that nothing that can melt or burn be within 6" of a flue pipe.

    Mark Fisher
    Allegany Inspection Service - Cumberland MD 21502 - 301-722-2224
    Home Inspections, Mold Testing, Thermal Imaging

  8. #8
    Join Date
    Mar 2007
    Location
    Spring Hill (Nashville), TN
    Posts
    5,851

    Default Re: Plastic hot water supply pipe too close to heater

    Quote Originally Posted by Matthew Liang View Post
    Thanks everybody for your comments.

    Tom, the gray pipe is PolyB which is used for all the supply pipes.

    So, I can conclude that the red pipe is PEX and it is too close to the heater.
    It is too close to the water heater exhaust, not the heater. You need to be specific with what you are trying to convey to your client.

    Scott Patterson, ACI
    Spring Hill, TN
    www.traceinspections.com

  9. #9
    Matthew Liang's Avatar
    Matthew Liang Guest

    Default Re: Plastic hot water supply pipe too close to heater

    Quote Originally Posted by Scott Patterson View Post
    It is too close to the water heater exhaust, not the heater. You need to be specific with what you are trying to convey to your client.
    Thank you so much, Scott.


  10. #10
    Join Date
    Dec 2009
    Location
    Corinth MS
    Posts
    14

    Default Re: Plastic hot water supply pipe too close to heater

    I know that the post is about the PEX pipe being too close to the water heater so I might be amiss but there might also an issue with the class b gas venting. I have never seen class b gas vent crimped. From the picture it looks like it might have been hand crimped at that.


  11. #11
    Join Date
    Mar 2007
    Location
    New Mexico
    Posts
    1,352

    Default Re: Plastic hot water supply pipe too close to heater

    I don't think that it B vent in the photo. The B vent probably (hopefully) starts above the photo. Probably single wall, hence the six inch space needed for the pex.

    Jim Robinson
    New Mexico, USA

  12. #12
    Matthew Liang's Avatar
    Matthew Liang Guest

    Default Re: Plastic hot water supply pipe too close to heater

    Quote Originally Posted by Jim Robinson View Post
    I don't think that it B vent in the photo. The B vent probably (hopefully) starts above the photo. Probably single wall, hence the six inch space needed for the pex.
    Hi Joe and Jim,
    Thank you for your comment.

    It is not B-vent. It goes up to join the former furnace vent, then to B-vent. See attached picture.

    Actually I cannot figure out what the pipe is at the corner. It is goes up into the ceiling and down to the crawlspace.

    ***IMPORTANT*** You Need To Register To View Images ***IMPORTANT*** You Need To Register To View Images

  13. #13
    Join Date
    Mar 2007
    Location
    Fletcher, NC
    Posts
    28,032

    Default Re: Plastic hot water supply pipe too close to heater

    Quote Originally Posted by Matthew Liang View Post
    Actually I cannot figure out what the pipe is at the corner. It is goes up into the ceiling and down to the crawlspace.
    Radon mitigation exhaust?

    Jerry Peck
    Construction/Litigation/Code Consultant - Retired
    www.AskCodeMan.com

  14. #14
    Matthew Liang's Avatar
    Matthew Liang Guest

    Default Re: Plastic hot water supply pipe too close to heater

    Quote Originally Posted by Jerry Peck View Post
    Radon mitigation exhaust?
    Hi Jerry,
    I have no idea about Radon test. This is a house in Vancouver BC Canada close to US border.

    Could someone shed a light on this?


  15. #15
    Join Date
    Mar 2007
    Location
    Fletcher, NC
    Posts
    28,032

    Default Re: Plastic hot water supply pipe too close to heater

    Quote Originally Posted by Matthew Liang View Post
    Hi Jerry,
    I have no idea about Radon test. This is a house in Vancouver BC Canada close to US border.

    Could someone shed a light on this?
    Matthew,

    Let's hope some of the people who do radon and know about radon mitigation respond - that is something I know little about.
    But I think I know that sucking the radon out of the crawlspace and dumping it into the attic is not a good thing ... does that duct go outside or end in the attic? Heck *I* would not even want a radon duct 'going through the house' in case there was any leakage.

    Jerry Peck
    Construction/Litigation/Code Consultant - Retired
    www.AskCodeMan.com

  16. #16
    Join Date
    Feb 2009
    Location
    Southern Vancouver Island
    Posts
    4,607

    Default Re: Plastic hot water supply pipe too close to heater

    There's no significant uranium in the ground so no radon threat in that part of the world.

    Maybe it's a dryer vent. Can't tell without more info.

    John Kogel, RHI, BC HI Lic #47455
    www.allsafehome.ca

  17. #17
    Join Date
    Mar 2007
    Location
    Near Philly, Pa.
    Posts
    1,682

    Cool Re: Plastic hot water supply pipe too close to heater

    Unlisted firestop, improper support, no firestop for pipe in corner regardless of whatever it is. Yes, 6" clearance off single walled vent connector.

    Radon mitigation is under positive vent pressure downstream of the inline blower so it should not be within the structure and discharge into the atmosphere-not attic. Radon mitigation is usually done with sch. 40 pvc cemented joints. INFILTEC Air Leakage Control - Radon Gas Mitigation & Blower Doors - test, testing

    HTH

    Keep the fire in the fireplace.

  18. #18
    Join Date
    Dec 2007
    Location
    Holladay, UT
    Posts
    577

    Default Re: Plastic hot water supply pipe too close to heater

    Could that pipe in corner be bringing in combustion air from attic. Sorry, I just went back and looked at post, didn't see the part where it goes down into the crawl space. Is furnace in crawlspace?

    Last edited by Tom Rees; 08-18-2012 at 07:04 AM.
    Tom Rees / A Closer Look Home Inspection / Salt Lake City, Utah
    http://acloserlookslc.com/

  19. #19
    Join Date
    Mar 2007
    Location
    Spring Hill (Nashville), TN
    Posts
    5,851

    Default Re: Plastic hot water supply pipe too close to heater

    Report it as an unknown pipe in corner.....

    Scott Patterson, ACI
    Spring Hill, TN
    www.traceinspections.com

  20. #20
    Join Date
    Mar 2007
    Location
    Fletcher, NC
    Posts
    28,032

    Default Re: Plastic hot water supply pipe too close to heater

    Quote Originally Posted by Scott Patterson View Post
    Report it as an unknown pipe in corner.....
    We know the pipe ... its name of Fred, what we do not know is why Fred is there and why it goes from the crawlspace and up through the ceiling.

    Jerry Peck
    Construction/Litigation/Code Consultant - Retired
    www.AskCodeMan.com

  21. #21
    Matthew Liang's Avatar
    Matthew Liang Guest

    Default Re: Plastic hot water supply pipe too close to heater

    Quote Originally Posted by Scott Patterson View Post
    Report it as an unknown pipe in corner.....
    Thank you, everybody, for your comment. I came to the house again today and found out that the pipe is a hot air supply pipe from crawlspace to 2nd floor bathroom.


  22. #22
    Join Date
    Dec 2008
    Location
    Maryland
    Posts
    2,809

    Default Re: Plastic hot water supply pipe too close to heater

    Radon mitigation needs a sealed conduit between the source and the exterior of the structure . PVC is used because it can be chemically bonded at the unions forming a continuous sealed conduit to remove the gas from under the basement slab.


  23. #23
    Join Date
    Jul 2008
    Location
    Snowbird (this means I'm retired and migrate between locations), FL/MI
    Posts
    4,086

    Default Re: Plastic hot water supply pipe too close to heater

    There should be no combustible form of tubing or piping in the top zone of the Cat. I fuel-fired water heater. That area is all encompasing to its diameter and for a height determined by its listing/approval (instructions) and venting type.Clearance to front of water heater, burner plate, no safe pan or drainage for same, TPRV discharge too high from floor, floor unprotected from same, no conversion to drainage, no proper termination of same; no sed trap before gas valve of appiance, improper shut-off valve, etc. etc.temperature transfer to hvac duct, leakage/spillage to hvac return.There are critical issues regarding the double draft hood, tape, clearances (not just to combustibles but required air space, heat reflective materials, form, sizing, non-support, configuration and manner of vent connector to b-vent system, more tape, etc. and sizing/configuration of orphaned gas-fired appliance venting. Dissimilar metal connections, heat sink, exposed insulation facing, holes in gyp separation, and many other issues referenced in your two other discussion topics wherein you've sprinkled additional photos of the same cluster of defects.


  24. #24
    Join Date
    Mar 2007
    Location
    Atlanta, Georgia
    Posts
    1,088

    Default Re: Plastic hot water supply pipe too close to heater

    Who makes the rule that it cannot be plastic within the first 18 inches? Is it code or manufacturers installation instructions? Looking for a reference please.

    Yes, I agree that it does not make good sense. Like to have a reference when challenged.

    "The Code is not a peak to reach but a foundation to build from."

  25. #25
    Join Date
    Mar 2007
    Location
    Fletcher, NC
    Posts
    28,032

    Default Re: Plastic hot water supply pipe too close to heater

    Quote Originally Posted by Bruce Ramsey View Post
    Who makes the rule that it cannot be plastic within the first 18 inches? Is it code or manufacturers installation instructions? Looking for a reference please.

    Yes, I agree that it does not make good sense. Like to have a reference when challenged.
    Depends. Heat sources? Electric water heaters? Gas water heaters?

    http://www.cbsupplies.ca/guides/VG_P...tall_Guide.pdf (go to page 16 & 18)

    Jerry Peck
    Construction/Litigation/Code Consultant - Retired
    www.AskCodeMan.com

  26. #26
    Join Date
    Mar 2007
    Location
    Atlanta, Georgia
    Posts
    1,088

    Default Re: Plastic hot water supply pipe too close to heater

    Ok. Good. Thank you. The PEX manufacturer says must be 6 inches from heat source for PEX.

    Lots of CPVC in my area. Got a reference for other than PEX?

    "The Code is not a peak to reach but a foundation to build from."

  27. #27
    Join Date
    Mar 2007
    Location
    Fletcher, NC
    Posts
    28,032

    Default Re: Plastic hot water supply pipe too close to heater

    Quote Originally Posted by Bruce Ramsey View Post
    The PEX manufacturer says must be 6 inches from heat source for PEX.
    Are you referring to a specific manufacturer when you say "The PEX manufacturer says must be 6 inches" or to that link?

    For CPVC: https://www.ppfahome.org/pdf/PPFA_CP...anual_2006.pdf (go to page 6, Water Heater Connections)

    Jerry Peck
    Construction/Litigation/Code Consultant - Retired
    www.AskCodeMan.com

  28. #28
    Join Date
    Mar 2007
    Location
    Atlanta, Georgia
    Posts
    1,088

    Default Re: Plastic hot water supply pipe too close to heater

    Quote Originally Posted by Jerry Peck View Post
    Are you referring to a specific manufacturer when you say "The PEX manufacturer says must be 6 inches" or to that link?

    For CPVC: https://www.ppfahome.org/pdf/PPFA_CP...anual_2006.pdf (go to page 6, Water Heater Connections)
    I was referring to the link you provided. Thank you for the two links.

    "The Code is not a peak to reach but a foundation to build from."

  29. #29
    Join Date
    Mar 2007
    Location
    Fletcher, NC
    Posts
    28,032

    Default Re: Plastic hot water supply pipe too close to heater

    Quote Originally Posted by Bruce Ramsey View Post
    The PEX manufacturer says must be 6 inches from heat source for PEX.
    Quote Originally Posted by Bruce Ramsey View Post
    I was referring to the link you provided. Thank you for the two links.
    That's not what that link says.

    Page 16 says a minimum of 12" above, and a minimum of 6" horizontally from, a high heat producing element such as recessed lights, vents, etc.

    However, on page 18 it says that a minimum of the first 18" above a gas water heater needs to be metal ... not withstanding that the 6" horizontally shown on page 16 still applies to the PEX beyond that first 18" of metal pipe.

    Jerry Peck
    Construction/Litigation/Code Consultant - Retired
    www.AskCodeMan.com

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •