Results 1 to 10 of 10

Thread: TPR air gap

  1. #1
    Join Date
    Mar 2007
    Location
    Orlando, FL
    Posts
    1,592

    Default TPR air gap

    TPR air gap and photo test on the new forum.

    Dom.

    ***IMPORTANT*** You Need To Register To View Images ***IMPORTANT*** You Need To Register To View Images
    OREP Insurance

  2. #2
    Join Date
    Mar 2007
    Location
    Capistrano Beach, CA
    Posts
    1,510

    Default Re: TPR air gap

    Congratulations Dom!

    You are the first person to post on the new board.

    I hope you like it!

    View The List Of InspectionNews Member Benefits!

    -----------------
    Sincerely,
    Brian Hannigan
    InspectionNews.net / InspectionReferral.com
    Helping Inspectors $ucceed Since 1997TM

    Facebook: https://www.facebook.com/InspectionNews
    Twitter: @InspectionNews

  3. #3
    Join Date
    Mar 2007
    Location
    Houston, Texas
    Posts
    294

    Smile Re: TPR air gap

    Dom,

    I have to say that the piping configuration in your photos is very interesting indeed. It displays both a strong affinity for the "spirit of the code" while at the same time displaying a total disregard for the "letter of the code".

    Of course, scientifically researching the presumed functionality of the presented configuration would cost many times more than just conforming to the "letter of the code".

    After all, there is an atmospheric "air gap" present draining into that "indirect waste" piping at the temperature and pressure relief valve piping "termination" is there not?

    And Code does not really "go" beyond the "proper" termination of the T&P piping does it? (except for grading and drainage issues). But then there is that pesky "outside" the structure issue isn't there?

    On the other hand, Code does not define the acceptablity of a given "waste drain" specifically built for T&P "atmosphereic" discharge purposes in this circumstance does it?


    Last edited by Phillip Stojanik; 04-01-2007 at 12:59 PM.

  4. #4
    Join Date
    Mar 2007
    Location
    Fletcher, NC
    Posts
    28,032

    Default Re: TPR air gap

    Dom,

    Those aren't any good.

    Did you open the T&P and test it?

    Water spurts out of that air gap all over. At least is did from all the ones like it I've tested.

    Like Phillip said ... trying to meet the 'intent' of the code without really understanding the 'reasoning' behind the 'wording' of the code.

    An air gap is not just to serve as an atmospheric breaker (except for hose bibbs), but to serve as an 'air space' across which cross or back contamination will be prevented. Those may serve as an atmospheric air break, however, being as this is not a hose bibb, it needs back flow protection which will also provide an 'air gap' (i.e., and 'air space') which will prevent cross or back contamination.

    Jerry Peck
    Construction/Litigation/Code Consultant - Retired
    www.AskCodeMan.com

  5. #5
    william siegel's Avatar
    william siegel Guest

    Default Re: TPR air gap

    Jerry,

    That is very similar to the ones in Miami I have been fighting over. The building department, however (stupidly) is allowing them. They dont seem to care.


  6. #6
    Tim Moreira's Avatar
    Tim Moreira Guest

    Default Re: TPR air gap

    Maybe that is supposed to vent the steam while the water goes to the drain.


  7. #7
    Join Date
    Mar 2007
    Location
    Spring Hill (Nashville), TN
    Posts
    5,851

    Default Re: TPR air gap

    It's also going into a PVC pipe that is not rated for that high of heat that will occur if the TPR releases.

    Scott Patterson, ACI
    Spring Hill, TN
    www.traceinspections.com

  8. #8
    Richard Rushing's Avatar
    Richard Rushing Guest

    Default Re: TPR air gap

    What Scott posted is the first thing that jumped out at me was the CPVC into PVC... It's just not rated for that temperature.


    Richard


  9. #9
    Join Date
    Mar 2007
    Location
    Fletcher, NC
    Posts
    28,032

    Default Re: TPR air gap

    Scott said: "It's also going into a PVC pipe that is not rated for that high of heat that will occur if the TPR releases."

    Richard said: "What Scott posted is the first thing that jumped out at me was the CPVC into PVC... It's just not rated for that temperature."

    Now wait just a minute guys ...

    Didn't we just have a long thread and debate over the heat of the water going out the T&P discharge pipe?

    Didn't you guys (or maybe it was someone else) tell me that it just dribbles and does not allow large amounts or HOT water or steam out?

    Bill,

    That's where I've seen them, except that I've always seen them doing it with copper.

    I would open the valve and, astonished, 'GASP! IT'S LEAKING!', I would pronounce to my client and whomever else was nearby. They would all rush in and ask 'WHAT'S LEAKING?', then I would show them.

    My client's never liked that and I recommended they call a plumber to correct it. The seller would say 'But it's never leaked before.'

    Jerry Peck
    Construction/Litigation/Code Consultant - Retired
    www.AskCodeMan.com

  10. #10
    Richard Rushing's Avatar
    Richard Rushing Guest

    Default Re: TPR air gap

    J.Peckl-- that was some OTHER kNuCkLeHeAd...

    RR


Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •