InspectionNews - Home Inspection



Welcome to the InspectionNews - Home Inspection forums.

You are currently viewing InspectionNews as a guest which gives you limited access to view most discussions but not pictures. There are over 6,300 inspectors who have already joined. By joining InspectionNews you will be able to see the pictures, have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features. Registration is fast and simple so please, join InspectionNews today!

If you have any problems with the registration process or your account login, please contact us.

Why join InspectionNews? Read the Testimonials
Reply
 
LinkBack Thread Tools Search this Thread
  #1 (permalink)  
Old 08-04-2007, 07:35 PM
Jeff Eastman Jeff Eastman is offline
Member
 
Join Date: Mar 2007
Location: gone
Posts: 245
Cold joint?
..............

Last edited by Jeff Eastman : 11-27-2007 at 07:31 PM.
Reply With Quote
Home inspection
  #2 (permalink)  
Old 08-05-2007, 12:53 AM
Matt Fellman Matt Fellman is offline
Member
 
Join Date: Mar 2007
Location: Oregon
Posts: 657
Re: Cold joint?
I can't make out too much from pics 2 & 3.... at first pic 1 seemed pretty severe but then I realized how close up it was. Still, that looks like more than just a cold joint.... but again, I can't tell too much from the pic. I'd need some more info to know for sure.

Any signs from inside?

Is it a basement or a crawl?

How old is the house?

Sloped floors, walls or anything of note in this area of the house?

I'd try to get to the sill plate and foundation inside this area and see what was going on. If all is well in all of these areas and none of the questions above raise more questions I'd lean towards thinking it was a bad pour or cold joint and was okay.... but, again, it's tough to say from those pics.
Reply With Quote
  #3 (permalink)  
Old 08-05-2007, 02:28 AM
Bruce Breedlove's Avatar
Bruce Breedlove Bruce Breedlove is offline
Member
 
Join Date: Mar 2007
Location: Colorado Springs, CO
Posts: 676
Re: Cold joint?
What is commonly called a cold joint is when fresh concrete is poured on top of (or adjacent to) concrete that has already begun to set up. This often happens in a large pour (e.g., a foundation wall or a large slab) where it takes a good deal of time for the pour to make the circuit back to the starting point. A cold joint can also occur when a delay occurs during the pour (e.g., a concrete truck is delayed or a blowout occurs in the formwork).

The interface between the two pours is the cold joint. The cold joint is noticeable by the difference in color of the concrete on either side of it. Cold joints are not normally a structural concern. (After my episode with a leaking honeycomb the other day I would not rule out the possibility of a cold joint leaking.) Good practice is to vibrate the concrete to blend the new and old concrete if possible to avoid a cold joint or to insert rebar into the old concrete to create a structural bridge between the two pours. If it is anticipated that the first-poured concrete will be set up beyond the point of the new concrete adhering to it a keyway can be formed into the first pour (possibly along with rebar dowels) to make a good structural connection between the two pours.

In Pic 1 it is hard to tell if that is a cold joint, a new foundation poured on top of an old foundation or parging on the upper part of the foundation.

I can't make out much from Pic 2. It looks like the bottom of the foundation flares out or is leaning quite a bit. Is it possible that the original foundation was stone and a concrete foundation was poured on top of (and perhaps inside of) it? When was the house built? (Stone foundations are not common after 1930 or so.)

In Pic 3 what you are looking at may be either a buttress or a mistake. It could also be the remnants of the foundation of a room that has long since been removed.

Hope that helps. It is hard to tell much from your pics.
__________________
"Baseball is like church. Many attend but few understand." Leo Durocher
Bruce Breedlove
www.avaloninspection.com
Reply With Quote
Home inspection
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Construction Joint needed? Jeff Eastman Exterior Systems: Home Inspection and Commercial Inspection 2 07-06-2007 12:45 PM
Brick Veneer Exterior Wall 90 deg inside joint imported_John Smith Exterior Systems: Home Inspection and Commercial Inspection 2 04-05-2007 07:52 PM


All times are GMT -7. The time now is 11:54 AM.


Design by Vjacheslav Trushkin.
Powered by vBulletin® Version 3.6.5
Copyright ©2000 - 2008, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.0.0 RC8
vB.Sponsors
All Rights Reserved. Hann Tech Marketing Link / InspectionNews.com / InspectionNews.net - No part of InspectionNews.net may be reproduced in any way, or by any means, without the prior written permission of InspectionNews.net. Use of any index or listing Software for the purpose of constructing a mailing list, creating promotional materials or producing a printed or electronic catalog of any kind is expressly forbidden without the prior written permission of InspectionNews.net - All text, graphics and design on InspectionNews.net is copyright by Hann Tech Marketing Links.
Ad Management by RedTyger